Department of Engineering, Engineering Technology and Surveying
PO Box 70552
213 Wilson Wallis Hall
Johnson City, TN 37614
Phone: (423) 439-7822
Fax-Admin: (423) 439-7830
Fax-Faculty: (423) 439-7750
Web Address: www.etsu.edu/cbat/applieddesign/
The Department of Engineering, Engineering Technology, and Surveying, a unit of the College of Business and Technology [CBAT], is one of the largest and most academically diverse units of East Tennessee State University. The Department offers undergraduate degree programs in numerous concentrations, undergraduate minors in two areas, and graduate degree programs in three concentrations. The Electriconics Engineering Technology program is accredited by the Engineering Technology Accreditation Commission (ETAC) of the Accreditation Board of Engineering (ABET), http://www.abet.org. Additionally, there are many majors and/or programs that are available through the Academic Common Market allowing out-of-state students to enroll at ETSU at in-state tuition rates.
The department’s administrative and faculty offices are housed in Wilson-Wallis Hall. https://www.etsu.edu/cbat/applieddesign/contactus.php
All non-technology coursework such as English, mathematics, and science is evaluated for transfer by an analyst in the Office of Admissions. All technology coursework submitted for transfer will be analyzed by the department chair or the appropriate program coordinator. The following criteria apply:
- Coursework must have been taken at a regionally accredited two- or four-year institution.
- Coursework must be equivalent to an ETSU course; if not, it will count as elective credit.
- Only coursework for which a grade of C (2.0) or higher was earned will be accepted for transfer credit for courses in English, mathematics, science, and technology.
- No associate degree coursework will be accepted for Engineering Technology coursework at the 4xxx level.
Upon admission, the transfer student may consult the corresponding academic advisor for an agreement listing the coursework that must be successfully completed by the student.
Students contemplating the transfer of their technology-based associate degree should read the policy statement regarding transfer student admissions elsewhere in this catalog and confer with the corresponding academic advisor with the Department of Engineering, Engineering Technology, and Surveying.
Electronics Engineering Technology Concentration
This concentration emphasizes electronics specialties in the areas of Telecommunications and Instrumentation and Automation. It prepares individuals for job opportunities in all areas of electronics with selection of the general specialty.
Students Transferring into Electronics Engineering Technology Concentration
All students, including transfer students, must complete the published curriculum in electronics engineering technology in effect the year of their entry into the program. All students transferring into the B.S. degree electronic engineering technology program must take a minimum of four electronics courses that must include ENTC 3310 - Circuit Analysis . No associate degree coursework will be accepted for electronic coursework at the 4XXX level.
If the transfer student is from a program that is not accredited by ABET, the required minimum must also include ENTC 3320 - Electronics II . It is the students’ responsibility to provide evidence that the transferred coursework was completed at an ABET-accredited institution.
Degree Requirements: 128 credits
|Major Total Requirement
| Major Core
|| (19 credits)
|| (46 credits)
| Electronic Electives
|| (11 credits)
| Specialty Electives
|| (11 credits)
Suggested Four-Year Program of Study: ENTC-BS (ELEC)
General Education Requirements
These requirements include earning 41-42 credits in Communication, Humanities and Fine Arts, Social and Behavior Sciences, History, Natural Sciences and Mathematics categories.
Major Specific courses listed in General Education Requirements:
Total Requirements for Engineering Technology Major: 87 credits
Engineering Technology Major Core Requirements: 19 credits
Electronics Engineering Concentration Requirements: 46 credits
Electronics Electives: 11 credits
Choose 11 credits from the following:
Specialty Electives: 11 credits
Choose one (1) area of courses for a total of 11 credits:
Instrumentation & Automation Area
If general area is selected by student, choose 11 credits from courses listed below:
Click here to view Degree and Graduation Requirements for all ETSU students.
CSCI 1100 or Proficiency exam: Must be completed to meet Bachelor’s Degree Requirements.
Most minors range from 18-24 credits. Those few minors with more than 24 credits may affect the number of free electives allowed.